0
TECHNICAL NOTES

Theoretical Investigation of Unsteady Squeeze Flow in a Curved Newtonian Squeeze Film

[+] Author and Article Information
R. Usha, P. Vimala

Department of Mathematics, Indian Institute of Technology, Madras, Chennai-600 036, India

J. Tribol 124(4), 865-869 (Sep 24, 2002) (5 pages) doi:10.1115/1.1467641 History: Received March 26, 2000; Revised January 22, 2002; Online September 24, 2002
Copyright © 2002 by ASME
Your Session has timed out. Please sign back in to continue.

References

Borgin,  P., and Tichy,  J. A., 1985, “Lubricating Films of a Viscoelastic Fluid, Including Fluid Inertia, Studied by a Linearization Method,” Int. J. Eng. Sci., 23, pp. 1135–1149.
Hashimoto,  H., and Wada,  S., 1986, “The Effects of Fluid Inertia Forces in Parallel Circular Squeeze Film Bearings Lubricated With Pseudoplastic Fluids,” ASME J. Tribol., 108, pp. 282–287.
Esmonde,  H., Fitzpatrick,  J. A., Rice,  H. J., and Axisa,  F., 1992, “Modelling and Identification of Nonlinear Squeeze Film Dynamics,” J. Fluids Struct. 6, pp. 223–248.
Bhat,  M. V., and Deheri,  G. M., 1993, “Magnetic-Fluid-Based Squeeze Film in Curved Porous Circular Discs,” J. Magn. Magn. Mater., 127, pp. 159–162.
Hashimoto,  H., 1994, “Viscoelastic Squeeze Film Characteristics with Inertia Effects Between Two Parallel Circular Plates Under Sinusoidal Motion,” ASME J. Tribol., 116, pp. 161–166.
Hashimoto,  H., 1995, “Squeeze Film Characteristics between Parallel Circular Plates Containing a Single Central Air Bubble in the Internal Flow Regime,” ASME J. Tribol., 117, pp. 513–518.
Tichy,  J. A., 1995, “A Porous Media Model for Thin Film Lubrication,” ASME J. Tribol., 117, pp. 16–21.
Han,  Y., and Rogers,  R. J., 1996, “Squeeze Film Force Modeling for Large Amplitude Motion Using an Elliptical Velocity Profile,” ASME J. Tribol., 118, pp. 687–692.
Usha,  R., and Rukmani,  R., 1998, “An Investigation of a Squeeze Film Between Two Plane Annuli,” ASME J. Tribol., 120, pp. 610–615.
Laun,  H. M., Rady,  M., and Hassager,  O., 1999, “Analytical Solutions for Squeeze Flow with Partial Wall Slip,” J. Non-Newtonian Fluid Mech., 81, pp. 1–15.
Shah,  R. C., and Bhat,  M. V., 2000, “Squeeze Film Based on Magnetic Fluid in Curved Porous Rotating Circular Plate,” J. Magn. Magn. Mater., 208, pp. 115–119.
San Andres,  L. A., and Vance,  J. M., 1986, “Effects of Fluid Inertia and Turbulence on the Force Coefficients for Squeeze Film Dampers,” ASME J. Eng. Gas Turbines Power, 108, pp. 332–339.
Hays,  D. F., 1963, “Squeeze Films for Rectangle Plates,” ASME J. Basic Eng., 85, pp. 243–246.
Murti,  P. R. K., 1975, “Squeeze Films in Curved Circular Plates,” ASME J. Lubr. Technol., 97, pp. 650–652.
Gupta,  J. L., and Vora,  K. H., 1980, “Analysis of Squeeze Films Between Curved Annular Plates,” ASME J. Lubr. Technol., 102, pp. 48–50.
Gupta,  R. S., and Kapur,  V. K., 1980, “The Simultaneous Effects of Thermal and Inertia in Curved Circular Squeeze Films,” ASME J. Lubr. Technol., 102, pp. 501–504.
Vora,  K. H., and Bhat,  M. V., 1980, “The Load Capacity of a Squeeze Film Between Curved Porous Roating Circular Plates,” Wear, 65, pp. 39–46.
Hasegawa,  E., 1985, “On Squeeze Film of a Curved Circular Plate,” Bull. JSME, 28, pp. 951–958.
Hasegawa,  E., Kanda,  T., and Watanabe,  H., 1986, “Squeeze Films Between a Rotating Curved Disk and a Plane Wall,” Bull. JSME, 29, pp. 1919–1926.
Crandall,  S. H., and El-Shafei,  A., 1993, “Momentum and Energy Approximations for Elementary Squeeze Film Damper Flows,” ASME J. Appl. Mech., 60, pp. 728–735.
Ishizawa,  S., 1966, “The Unsteady Laminar Flow Between Two Parallel Discs With Arbitrarily Varying Gap Width,” Bull. JSME, 9, pp. 533–550.

Figures

Grahic Jump Location
Curved squeeze film geometry
Grahic Jump Location
Dimensionless normal force on the curved disk-sinusoidal motion, H(r,t)=h(t)f(r);c̄>0: concave; c̄<0: convex
Grahic Jump Location
Dimensionless normal force-sinusoidal motion—a comparison for the case of a flat upper surface
Grahic Jump Location
Squeeze film force variation for sinusoidal motion –⋅– Hashimoto and Wada 2; Newtonian case.
Grahic Jump Location
Central film thickness variation for constant force squeezing state. (a), (b)—concave disk; (c), (d)—convex disk.

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In