Research Papers: Other (Seals, Manufacturing)

Theoretical Analysis of the Static Characteristics of the Carbon Segmented Seal

[+] Author and Article Information
Mihai Arghir

PPRIME Institute,
UPR CNRS 3346,
Université de Poitiers,
Chasseneuil Futuroscope 86962, France

Antoine Mariot

Centre National d'Etudes Spatiales,
Paris 75001, France;
PPRIME Institute,
UPR CNRS 3346,
Université de Poitiers,
Chasseneuil Futuroscope 86962, France

1Present address: SAFRAN Aircraft Engines, Villaroche 92141, France.

Contributed by the Tribology Division of ASME for publication in the JOURNAL OF TRIBOLOGY. Manuscript received October 26, 2016; final manuscript received February 21, 2017; published online June 30, 2017. Assoc. Editor: Min Zou.

J. Tribol 139(6), 062202 (Jun 30, 2017) (11 pages) Paper No: TRIB-16-1340; doi: 10.1115/1.4036272 History: Received October 26, 2016; Revised February 21, 2017

The segmented carbon seal is regularly used for sealing bearing chambers of aeronautical turboengines or as part of a buffer seal in space turbopumps. The seal operates with contaminated air or with an inert gas and is made of many identical carbon segments (generally three or six) with reciprocally overlapping ends. The segments are pressed against the rotor by the pressure difference between the upstream and the downstream chambers and by a circumferential (garter) spring. The pressure difference and an axial spring press the segments also against the stator. The inner cylindrical surface of each segment is provided with pads that create an aerodynamic lift proportional to the rotor speed. Following this lift force, the segments of the seal are pushed away from the rotor and the seal opens. The contact between the rotor and the segments is lost, and an axial leakage path is thus created. Although it was developed since long, a model for calculating the characteristics of the segmented seal is completely absent from the scientific literature. The goal of the present work is to fill this gap at least for the static characteristics (leakage and torque). The analysis is carried out for a single segment of the seal by supposing that all the segments have the same characteristics. Each segment has a planar motion (i.e., three degrees-of-freedom (3DOF)), and therefore the film thickness under each pad is not uniform. Given the stationary operating conditions (pressure difference and rotation speed), the present model calculates the equilibrium position of each segment on the bases of the lift and the friction force acting on the pads, the friction forces acting on the nose of the seal, and the radial and axial springs. Once found the static equilibrium position, the leakage and the torque of the seal are calculated. A parametric study enlightens the importance of the pad waviness, the pocket depth, and the spring forces on the characteristics of the segmented seal.

Copyright © 2017 by ASME
Your Session has timed out. Please sign back in to continue.


Oike, M. , Nosaka, M. , Watanabe, Y. , Kikuchi, M. , and Kamijo, K. , 1988, “ Experimental Study on High-Pressure Gas Seals for a Liquid Oxygen Turbopump,” STLE Trans., 31(1), pp. 91–97. [CrossRef]
Oike, M. , Nosaka, M. , Kikuchi, M. , Watanabe, Y. , and Kamijo, K. , 1990, “ Study on a Carbon Segmented Circumferential Seal for a Liquid Oxygen Turbopump,” Japan International Tribology Conference, Nagoya, Japan, Oct. 29–Nov. 1, pp. 283–288.
Nosaka, M. , and Oike, M. , 1990, “ Shaft Seals of Turbopumps for Rockets,” Jpn. J. Tribol., 35(4), pp. 411–421.
Oike, M. , Nosaka, M. , Kikuchi, M. , and Watanabe, Y. , 1992, “ Performance of a Segmented Circumferential Seal for a Liquid Oxygen Turbopump (Part 1): Sealing Performance,” Jpn. J. Tribol., 37(4), pp. 511–523.
Oike, M. , Nagao, R. , Nosaka, M. , Kamijo, K. , and Jinnouchi, T. , 1995, “ Characteristics of a Shaft Seal System for the LE-7 Liquid Oxygen Turbopump,” AIAA Paper No. 95-3102.
Burcham, R. E. , 1978, “ Liquid Rocket Engine Turbopump Rotating-Shaft Seal,” Report No. NASA S-8121.
Burcham, R. E. , 1983, “ High-Speed Cryogenic Self-Acting, Shaft Seals for Liquid Rocket Turbopumps,” Report No. NASA CR-168194.
Solidworks, 2017, “Solidworks Flow Simulation,” DASSAULT SYSTEMES, Vélizy-Villacoublay, France, accessed Jan. 12, 2017, http://www.solidworks.fr/sw/products/simulation/flow-simulation.htm
Arghir, M. , Le Lez, S. , and Frêne, J. , 2006, “ Finite Volume Solution of the Compressible Reynolds Equation—Linear and Non Linear Analysis of Gas Bearings,” Proc. Inst. Mech. Eng., Part J, 220(7), pp. 617–627. [CrossRef]
Constantinescu, V. N. , 1969, Gas Lubrication, ASME, United Engineering Center, New York.
Crolet, A. , 2008, “ Contribution à l'étude de l'influence du Comportement Vibratoire du Système ‘Pièce-Outil-Machine’ sur la Qualité de Surface Obtenue en Tournage de Superfinition,” Thèse de Doctorat de l'Université de l'Institut Polytechnique de Lorraine, Nancy, France.
Johnson, K. L. , 1985, Contact Mechanics, Cambridge University Press, Cambridge, UK.
Greenwood, J. A. , and Williamson, J. B. P. , 1966, “ Contact of Nominally Flat Surfaces,” Proc. R. Soc. London A, 295(1442), pp. 300–319. [CrossRef]
Lebeck, A. O. , 1991, Principles and Design of Mechanical Face Seals, John Wiley & Sons, Inc., Hoboken, NJ.
Kalker, J. J. , Dekking, F. M. , and Vollebregt, E. A. H. , 1997, “ Simulation of Rough, Elastic Contacts,” ASME J. Appl. Mech., 64(2), pp. 361–368. [CrossRef]
van Ostayen, R. A. J. , van Beek, A. , and Ros, M. , 2004, “ A Mathematical Model of the Hydro-Support: An Elasto-Hydrostatic Thrust Bearing With Mixed Lubrication,” Tribol. Int., 37(8), pp. 607–616. [CrossRef]
IMSL Fortran Numerical Library, 2017, “Embeddable Numerical Analysis Functions for Fortran Applications,” Rogue Wave Software, Inc., Louisville, CO, accessed Jan. 12, 2017, http://www.roguewave.com/products-services/imsl-numerical-libraries/fortran-libraries


Grahic Jump Location
Fig. 1

Exploded view of the segmented seal

Grahic Jump Location
Fig. 2

Enlarged detail of the segmented seal

Grahic Jump Location
Fig. 3

Pressure field from a computational fluid dynamics (CFD) analysis (a) under the pad and (b) under the lip

Grahic Jump Location
Fig. 4

Simplified view of the forces acting on the segment (a) at nominal speed and (b) after coast-down

Grahic Jump Location
Fig. 5

Calculation domain for the pad and the lip

Grahic Jump Location
Fig. 6

Pressure field on a pocketed pad

Grahic Jump Location
Fig. 7

Typical pressure variation under the lip

Grahic Jump Location
Fig. 8

The displacements of the segment

Grahic Jump Location
Fig. 9

Forces acting on a segment

Grahic Jump Location
Fig. 10

Relative displacements of the segments after seal opening

Grahic Jump Location
Fig. 11

The unwrapped geometry of the segment (all dimensions are in mm)

Grahic Jump Location
Fig. 12

Fluid pressures (left) and contact pressures (right) for pads 1 (top) to 3 (bottom); all pressures are in (Pa) and the lengths in (m)

Grahic Jump Location
Fig. 13

The displacements of the segment (left) and of the seal leakage flow and dissipated power (right) versus different parameters: (a) rotation speed, (b) pocket depth, (c) pocket length, (d) pocket width, (e) magnitude of the axial spring force, (f) magnitude of the garter spring force, and (g) amplitude of the waviness errors

Grahic Jump Location
Fig. 14

Representation of the rough surface




Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In