Zirkelback,
N., and San Andres,
L., 1998, “Finite Element Analysis of Herringbone Groove Journal Bearings: A Parametric Study,” ASME J. Tribol., 120, pp. 234–240.
Zhu,
J., and Ono,
K., 1999, “A Comparison Study on the Performance of Four Types of Oil Lubricated Hydrodynamic Thrust Bearings for Hard Disk Spindles,” ASME J. Tribol., 121, pp. 114–120.
Jang,
G. H., and Kim,
Y. J., 1999, “Calculation of Dynamic Coefficients in a Hydrodynamic Bearing Considering Five Degrees of Freedom for a General Rotor-Bearing System,” ASME J. Tribol., 121, pp. 499–505.
Jang,
G. H., and Chang,
D. I., 2000, “Analysis of a Hydrodynamic Herringbone Grooved Journal Bearing Considering Cavitation,” ASME J. Tribol., 122, pp. 103–109.
Hirayama, T., and Yabe, H., 2001, “A Study on Operating Characteristics of Spiral Grooved Journal Bearings—An Investigation of the Boundary Contour of Gas–Liquid Interface,” Proc. International Tribology Conference Nagasaki, 2000, K. Ichimaru et al., eds., JST, Tokyo, III, pp. 1633–1638.
Zhang, Q. D., Winoto, S. H., Chen, S. X., and Chong, H. C., 2001, “Design of Fluid Film Bearing for Spindle Motor in Hard Disk Drives,” Proc. International Tribology Conference Nagasaki, 2000, K. Ichimaru et al., eds., JST, Tokyo, III, pp. 1645–1650.
Jang,
G. H., and Yoon,
J. W., 2002, “Nonlinear Dynamic Analysis of a Hydrodynamic Journal Bearing Considering the Effect of a Rotating or Stationary Herringbone Groove,” ASME J. Tribol., 124, pp. 297–304.
Jang,
G. H., and Yoon,
J. W., 2003, “Stability Analysis of a Hydrodynamic Journal Bearing With Rotating Herringbone Grooves,” ASME J. Tribol., 125, pp. 291–300.
Zang, Y., and Hatch, M. R., 1995, “Analysis of Coupled Journal and Thrust Hydrodynamic Bearing Using a Finite-Volume Method,” Advances in Information Storage and Processing Systems, ISPS-Vol. 1, pp. 71–79.
Rahman, M., and Leuthold, H., 2001, “Computer Simulation of a Coupled Journal and Thrust Hydrodynamic Bearing Using a Finite-Element Method,” Proc. International Tribology Conference Nagasaki, 2000, K. Ichimaru et al., eds., JST, Tokyo, III, pp. 1639–1644.
Wang,
Y., Wang,
Q. J., and Lin,
C., 2003, “Mixed Lubrication of Coupled Journal-Thrust-Bearing Systems Including Mass Conserving Cavitation,” ASME J. Tribol., 125, pp. 747–755.
Hori, Y., and Okoshi, K., 1976, “Stability of a Rotating Shaft Supported by Porous Bearings,” Proc. JSLE-ASLE International Lubrication Conference, 1975, T. Sakurai, ed., Elsevier, Amsterdam, pp. 333–340.
Kaneko,
S., Hashimoto,
Y., and I,
H., 1997, “Analysis of Oil–Film Pressure Distribution in Porous Journal Bearings Under Hydrodynamic Lubrication Conditions Using an Improved Boundary Condition,” ASME J. Tribol., 119, pp. 171–178.
Meurisse,
M.-H., and Giudicelli,
B., 1999, “A 3D Conservative Model for Self-Lubricated Porous Journal Bearings in a Hydrodynamic Steady State,” ASME J. Tribol., 121, pp. 529–537.
Vohr,
J. H., and Chow,
C. Y., 1965, “Characteristics of Herringbone-Grooved Gas-Lubricated Journal Bearings,” ASME J. Basic Eng., 87, pp. 568–578.
Hamrock, B. J., 1994, Fundamentals of Fluid Film Lubrication, McGraw-Hill, New York.
