Wire saw slicing is a cost effective technology with high surface quality for slicing large diameter silicon wafers. Though wire saws have been deployed to cut polycrystalline and single crystal silicon ingot since the early 1990s, very little is known about the fundamental cutting process. We investigate this manufacturing process and propose a contact stress model of wire saw slicing that illustrates the interactions among the wire, ingot, and abrasives (e.g., SiC) carried by the slurry. Stresses created by wire saw slicing silicon wafers are analyzed in this paper. During the cutting process, the wire moves at high speed (5–15 m/s) with respect to the silicon ingot. The abrasives in the slurry are lose third-body particles caught between the wire and ingot at the contact surface. The forces applied by the wire carry the abrasive particles and cause them to roll on the surface and at the same time to be constrained to indent the surface. Such rolling-indenting interactions result in the formation of isolated chips and surface cracks. The cracks and discontinuity on the surface also cause high stress concentration. As a result, the material is cut and removed. The stress fields of a single circular cone of the abrasive particle indenting on silicon crystal with normal and tangential forces can be calculated and analyzed from the modeling equations and boundary conditions. The stresses are expressed with dimensionless stress measures, as functions of normalized geometric parameters. The results show that the maximum normal stress occurs at the indentation point, while the maximum shear stress (σzx) occurs below the surface of contact, as expected. Such subsurface shear facilitates the peeling effects of the silicon cracks. Both the normal and tangential forces applied at the contacts are incorporated in the model. The model is very effective in explaining and predicting the behaviors and distributions of stresses during the cutting process, and can be used to determine the optimal geometry of the abrasive particles in the rolling-indenting process.
Skip Nav Destination
e-mail: kao@mal.eng.sunysb.edu
Article navigation
June 1998
Special Section Technical Papers
Modeling Stresses of Contacts in Wire Saw Slicing of Polycrystalline and Crystalline Ingots: Application to Silicon Wafer Production
J. Li,
J. Li
Department of Mechanical Engineering, SUNY at Stony Brook, Stony Brook, NY 11794-2300
Search for other works by this author on:
I. Kao,
I. Kao
Department of Mechanical Engineering, SUNY at Stony Brook, Stony Brook, NY 11794-2300
e-mail: kao@mal.eng.sunysb.edu
Search for other works by this author on:
V. Prasad
V. Prasad
Department of Mechanical Engineering, SUNY at Stony Brook, Stony Brook, NY 11794-2300
Search for other works by this author on:
J. Li
Department of Mechanical Engineering, SUNY at Stony Brook, Stony Brook, NY 11794-2300
I. Kao
Department of Mechanical Engineering, SUNY at Stony Brook, Stony Brook, NY 11794-2300
e-mail: kao@mal.eng.sunysb.edu
V. Prasad
Department of Mechanical Engineering, SUNY at Stony Brook, Stony Brook, NY 11794-2300
J. Electron. Packag. Jun 1998, 120(2): 123-128 (6 pages)
Published Online: June 1, 1998
Article history
Received:
March 12, 1997
Revised:
January 29, 1998
Online:
November 6, 2007
Citation
Li, J., Kao, I., and Prasad, V. (June 1, 1998). "Modeling Stresses of Contacts in Wire Saw Slicing of Polycrystalline and Crystalline Ingots: Application to Silicon Wafer Production." ASME. J. Electron. Packag. June 1998; 120(2): 123–128. https://doi.org/10.1115/1.2792595
Download citation file:
Get Email Alerts
Anand Model Constants of Sn-Ag-Cu Solders: What Do They Actually Mean?
J. Electron. Packag
Enhancing Mechanical Reliability of Silver-Sintered Joints With Copper Nanowires in High-Power Electronic Devices
J. Electron. Packag (December 2024)
Special Issue on InterPACK2023
J. Electron. Packag (December 2024)
Related Articles
Interior Stress for Axisymmetric Abrasive Indentation in the Free Abrasive Machining Process: Slicing Silicon Wafers With Modern Wiresaw
J. Electron. Packag (September,1999)
Elasto-Hydrodynamic Interaction in the Free Abrasive Wafer Slicing Using a Wiresaw: Modeling and Finite Element Analysis
J. Tribol (April,2000)
Study of Ductile-to-Brittle Transition in Single Grit Diamond Scribing of Silicon: Application to Wire Sawing of Silicon Wafers
J. Eng. Mater. Technol (October,2012)
Free Abrasive Machining in Slicing Brittle Materials With Wiresaw
J. Electron. Packag (September,2001)
Related Proceedings Papers
Related Chapters
Use of Large Standoff Magnetometry for Geohazard Pipeline Integrity Investigations
Pipeline Integrity Management Under Geohazard Conditions (PIMG)
Completing the Picture
Air Engines: The History, Science, and Reality of the Perfect Engine
Concluding Remarks and Future Work
Ultrasonic Welding of Lithium-Ion Batteries